Sizing a rotary valve correctly is critical to keeping your bulk material handling line efficient. If a valve is undersized, material backs up into your hoppers and dust collectors. If it is oversized, the valve runs too slowly, pocket fill efficiency drops, and unnecessary air leakage occurs across the seal.
To ensure your Pyramid rotary valve delivers optimal performance, the engineering team at Shree Techno Engineers uses a straightforward volumetric calculation. Here is a step-by-step guide to calculating your required capacity in Tons Per Hour (TPH).
1. Key Parameters Needed for Sizing
Before calculating capacity, you need four key values regarding your operating environment and material:
- Desired Capacity (TPH): The target weight of material you need to move per hour.
- Material Bulk Density: The weight of your material per unit volume, usually measured in pounds per cubic foot or kilograms per cubic meter (for example, fine fly ash weighs around 40 to 45 pounds per cubic foot).
- Valve Pocket Displacement: The total internal volume discharged per complete 360-degree revolution of the rotor (measured in cubic feet or liters per revolution).
- Pocket Fill Factor: The percentage of each rotor pocket that actually fills with material during operation.
2. Understanding the Pocket Fill Factor
A rotor pocket rarely fills to 100 percent capacity during continuous operation. As the rotor turns, material falls into the pocket by gravity, while air inside the pocket escapes upward.
- Free-Flowing Materials (70% to 80% Fill): Dry, granular materials like small coal granules fill pockets quickly.
- Fine or Sluggish Powders (50% to 60% Fill): Fluidized powders or fine fly ash trap air, reducing the effective fill volume.
- High-Speed Operation: Running a rotor too fast (above 20 RPM) reduces the time available for material to enter the pocket, lowering the fill factor significantly.
3. The Step-by-Step Calculation Formula
To find the required displacement per hour, follow this basic formula:
- Step A: Determine Required Volumetric Flow Rate
Divide your required hourly weight (TPH) by the bulk density of your material to get the total volume needed per hour.
- Step B: Apply the Pocket Fill
Factor Divide your total required volume by your estimated fill factor (e.g., 0.65 for typical fine coal or ash) to adjust for incomplete pocket loading.
- Step C: Calculate Required RPM
Divide the adjusted hourly volume by 60 to get the required volume per minute. Then, divide that number by your valve’s displacement per revolution to find the target rotor speed in Revolutions Per Minute (RPM).
Sizing Parameter Reference Chart
| Material Type | Typical Bulk Density | Recommended Fill Factor | Target Rotor Speed |
| Crushed Coal | 45 to 50 lbs/cu.ft | 75% to 85% | 12 to 18 RPM |
| Fly Ash | 40 to 45 lbs/cu.ft | 50% to 60% | 10 to 15 RPM |
| Biomass Pellets | 35 to 40 lbs/cu.ft | 65% to 75% | 14 to 20 RPM |
| Coarse Bottom Ash | 55 to 60 lbs/cu.ft | 60% to 70% | >8 to 12 RPM |
4. Why Rotor RPM Matters for Equipment Lifespan
Running a small valve at a high speed (e.g., 30 RPM) to meet a high TPH requirement causes accelerated wear on abrasive ash lines. Higher speeds increase friction between the rotor tips and housing wall while increasing displacement air leakage.
The Golden Rule: It is almost always better to select a larger displacement valve running at a slower speed (10 to 15 RPM) than a smaller valve spinning rapidly. Running slower extends seal life, preserves internal clearances, and lowers overall maintenance costs.
Conclusion: Let Us Do the Math For You
Accurate sizing balances bulk density, fill factors, and mechanical speed to deliver long-term reliability. At Shree Techno Engineers, we double-check all volumetric calculations prior to manufacturing to guarantee that your Pyramid brand valve meets your exact process goals.
Do you need help calculating the exact valve capacity for an upcoming project?
Contact the technical engineering desk at Shree Techno Engineers today. Provide us with your material type and target TPH, and we will send you a full sizing verification sheet.
Contact Now



Users Today : 2
Users This Month : 424
Total views : 6110